RTMPL: A structured programming and documentation utility for real-time multiprocessor simulations

The NASA Lewis Research Center is developing and evaluating experimental hardware and software systems to help meet future needs for real time simulations of air-breathing propulsion systems. The Real Time Multiprocessor Simulator (RTMPS) project is aimed at developing a prototype simulator system that uses multiple microprocessors to achieve the desired computing speed and accuracy at relatively low cost. Software utilities are being developed to provide engineering-level programming and interactive operation of the simulator. Two major software development efforts were undertaken in the RTMPS project. A real time multiprocessor operating system was developed to provide for interactive operation of the simulator. The second effort was aimed at developing a structured, high-level, engineering-oriented programming language and translator that would facilitate the programming of the simulator. The Real Time Multiprocessor Programming Language (RTMPL) allows the user to describe simulation tasks for each processor in a straight-forward, structured manner. The RTMPL utility acts as an assembly language programmer, translating the high-level simulation description into time-efficient assembly language code for the processors. The utility sets up all of the interfaces between the simulator hardware, firmware, and operating system

Simulating a small turboshaft engine in real-time multiprocessor simulator (RTMPS) environment

A Real-Time Multiprocessor Simulator (RTMPS) has been developed at NASA Lewis Research Center. The RTMPS uses parallel microprocessors to achieve computing speeds needed for real-time engine simulation. This report describes the use of the RTMPS system to simulate a small turboshaft engine. The process of programming the engine equations and distributing them over one, two, and four processors is discussed. Steady-state and transient results from the RTMPS simulation are compared with results from a main-frame-based simulation. Processor execution times and the associated execution time savings for the two and four processor cases are presented using actual data obtained from the RTMPS system. Included is a discussion of why the minimum achievable calculation time for the turboshaft engine model was attained using four processors. Finally, future enhancements to the RTMPS system are discussed including the development of a generalized partitioning algorithm to automatically distribute the system equations among the processors in optimum fashion

Partitioning and packing mathematical simulation models for calculation on parallel computers

The development of multiprocessor simulations from a serial set of ordinary differential equations describing a physical system is described. Degrees of parallelism (i.e., coupling between the equations) and their impact on parallel processing are discussed. The problem of identifying computational parallelism within sets of closely coupled equations that require the exchange of current values of variables is described. A technique is presented for identifying this parallelism and for partitioning the equations for parallel solution on a multiprocessor. An algorithm which packs the equations into a minimum number of processors is also described. The results of the packing algorithm when applied to a turbojet engine model are presented in terms of processor utilization

Method of discrete modeling and its application to estimation of TF30 engine variables

A method of discrete modeling is presented that effectively isolates steady state model accuracy from dynamic model accuracy. The steady state model may be generated from the engine design equations with any desired degree of accuracy. The dynamic model is generated by applying a step disturbance of a manipulated variable to an open loop engine simulation. The sampled response of the variable is combined with the steady state model's response to form a set of weighting factors. These weighting factors are then used to weight past values of the manipulated variable, thus forming the dynamic model. The method is used to estimate various TF30-P-3 engine variables. A dynamic trim function is developed to compensate for the dynamic nonlinearities of the variables as well as for inaccuracies in dynamic definition. The trim function is shown to be realted to the square root of the sum of the squares of the weighting factors obtained at various engine operating conditions. Finally, the estimation of variables without dynamic modeling is discussed

Self-teaching digital-computer program for fail-operational control of a turbojet engine in a sea-level test stand

The design and evaluation are described of a digital turbojet engine control which is capable of sensing catastrophic failures in either the engine rotor speed or the compressor discharge static-pressure signal and is capable of switching control modes to maintain near normal operation. The control program was developed for and tested on a turbojet engine located in a sea-level test stand. The control program is also capable of acquiring all the data that are necessary for the fail-operational control to function

Hardware for a real-time multiprocessor simulator

The hardware for a real time multiprocessor simulator (RTMPS) developed at the NASA Lewis Research Center is described. The RTMPS is a multiple microprocessor system used to investigate the application of parallel processing concepts to real time simulation. It is designed to provide flexible data exchange paths between processors by using off the shelf microcomputer boards and minimal customized interfacing. A dedicated operator interface allows easy setup of the simulator and quick interpreting of simulation data. Simulations for the RTMPS are coded in a NASA designed real time multiprocessor language (RTMPL). This language is high level and geared to the multiprocessor environment. A real time multiprocessor operating system (RTMPOS) has also been developed that provides a user friendly operator interface. The RTMPS and supporting software are currently operational and are being evaluated at Lewis. The results of this evaluation will be used to specify the design of an optimized parallel processing system for real time simulation of dynamic systems

A digital computer propulsion control facility: Description of capabilities and summary of experimental program results

Flight weight digital computers are being used today to carry out many of the propulsion system control functions previously delegated exclusively to hydromechanical controllers. An operational digital computer facility for propulsion control mode studies has been used successfully in several experimental programs. This paper describes the system and some of the results concerned with engine control, inlet control, and inlet engine integrated control. Analytical designs for the digital propulsion control modes include both classical and modern/optimal techniques

Frequency response and transfer functions of a nuclear rocket engine system obtained from analog computer simulation

Frequency response and transport functions for NERVA-type rocket engin

An approach to real-time simulation using parallel processing

A preliminary simulator design that uses a parallel computer organization to provide accuracy, portability, and low cost is presented. The hardware and software for this prototype simulator are discussed. A detailed discussion of the inter-computer data transfer mechanism is also presented

Controls analysis of nuclear rocket engine at power range operating conditions

Control analysis of NERVA engine at power range operating condition